2000W Wind Generator

- Brushless 3-phase permanent magnet generator
- 2kw (Max. 3kw)
- For Use With 24V, 36V, 48V
- CE Certification
The OEM 2KW Wind Generator has been carefully engineered and is of Heavy Duty Industrial Construction. Made of heavy gauge steel, Powder Coated, and designed to last for 10 to 20 years. The Generator, Nacelle, Blades, Dynamic Braking & Dump Load have a total weight of 37 kilograms.

All parts are guaranteed for 3 years against defects of material or workmanship. The windmill can be used to charge a 24V battery bank, If you have an “annual wind speed " of 11 MPH at your site you can expect to generate 5,840 Kilowatts per year. If you pay the utility company $0.12 cents per KWH, the OEM 2KW Wind Generator will pay for itself in
One Year
!

Power curve for charging 24V battery banks!


Packing for Generator , & Nacelle with Styrofoam and double thick Export Carton


100Amp @ 1600Volt Yaw with double bearing & slip ring assembly
Bridge Rectifier

This is a heavy duty Dump Load Which Contains two large two ohm wire wound Resistors it has been
especially Designed As a dump load for Wind Generator Use.

The one millimeter steel case is gray Powder coated for many years of heavy use.

The wiring terminals have an extra cover, to protect the terminals and to assure safe operation and use.

Dynamic Braking System, this unit will Automatically monitor the rotor speed and keep it at or below 500
RPM. When the wind is very strong, and Dynamic Braking is activated.
The power from the generator is diverted to the Dump Load, which slows the rotor until it is slightly
below 500 RPM, this allows you to get the most watts possible from the wind.

Other Accessories;


USD 326
FOB Ningbo China
( not included with the generator )

The Grid-Tie Inverter has-been designed specially for use with OEM windmills, it is connected on one end to the DC supply from the windmill & the other end connects directly any wall outlet in your home. This will cause your electric meter to run “backward” or slow if you are using more electricity than the windmill is generating. No controller is needed.

Output can be switched between 110 VAC or 240 VAC.

The Grid-Tie Inverter, has the function of “Anti-Islanding Protection”. If the grid is down, the grid-tie inverter will switch off.


USD 298
FOB Ningbo China
( not included with the generator )

This OEM1000 Watt Battery Charge Controller receive DC from the Wind Generator. Its function is to prevent your batteries from being “over charged or over discharged”.

Display lights show the working status of the controller itself.


US$ 76.00
FOB Ningbo China
( not included with the generator )

The OEM data Recorder is a powerful tool unique to OEM that allows you to record the windmills performance to a computer 24 hours a day.

The data can be viewed in graph form, as well as plotted to a power curve graph in respect to RPM.

The recorder will allow for 4 parameters to be recorded, Battery Voltage, Amps Generated, Windmill RPM, & Wind Speed (with the use of an optional Anemometer not supplied).



The tower is available in 3 meter segments (the photo to the right) consist
of 4 segments plus a top 3 meter section for attaching the Nacelle of the
Windmill. The tower is available in 15 meters, 18 meters, 21 meters &
24 meter heights and is painted with primer paint.

The tower in the photo was assembled and raised by two men using only
hand tools, and a small hand operated chain hoist.

These towers are made to order and are not stocked, manufacturing
Takes from 4 to 6 weeks.

15 meters US $2000.00 FOB Ningbo China
18 meters US $2400.00 FOB Ningbo China
21 meters US $2800.00 FOB Ningbo China
24 meters US $3200.00 FOB Ningbo China